0
What type and size is the bolt holding the old belt tensioner on a 1994 2.3 Ranger you can't see what type bolt there is it feels like a star or Allen wrench type?
Wiki User
∙ 14y ago
The cap takes a T50, I am looking for the bolt size myself. My mechanic says it is probably metric, I would really like to know before I cut the head off to yank the old tensioner. If you know, please let me know.
An additional problem with this job is that the clearance is very tight, I tried to use a l-type torx wrench and a piece of pipe. The head of the bolt unfortunately was already stripped out so I am declaring war on the bolt. This agression will not stand.
thanks
jack
Wiki User
∙ 14y ago
Add your answer:
Earn +20 pts
What are the release dates for The George Burns and Gracie Allen Show - 1950 Holding Out 1-11?
The George Burns and Gracie Allen Show - 1950 Holding Out 1-11 was released on: USA: 15 February 1951
Who was the voice behind Buzz Light Year in Toy Story?
The space ranger Buzz Lightyear is voiced by Tim Allen.
How do you shorten a chainsaw chain?
You really should not need to as there should be a tensioner at the back of the blade under the cover. Some chainsaw are tool free (thumb tap) others may require Allen keys etc to release and tighten the tensioner but don't leave it to tight there should be a certain amount of slack.
How do i Adjust height on craftsman high wheel trimmer?
I adjusted mine by loosening the Allen nut holding the head to the shaft and sliding it up, and then tightening the Allen nut again. I also adjusted the handle to a height that tends to make me lift the head a little when I walk behind the trimmer. Hope this helps....
Is Ted Allen related to Woody Allen?
Woody Allen is a stage name. His birth name is Allen Stewart Konigsberg.
Pulley tensioner replacement percent Ford Ranger xlt 3.2l 2wd instructions do use an ALLEN wrench to loosen the spring or is it a special tool?
pulley tensioner replacement%ford ranger xlt 3.2l 2wd instructions. do use an ALLEN wrench to loosen the spring or is it a special tool
How do you release the tension for a serpentine beltin an Isuzu Rodeo?
Don't know what year you have but try this:The tensioner is located above the alternator. If you have an 8mm Allen wrench, use it to turn the tensioner arm clockwise with one hand, and remove the drive belt with the other. If you don't have the Allen wrench, use any 15mm wrench instead at the tensioner pulley nut to achieve the same.
On a 1992 Chevy lumina van there are Allen head bolts holding on the brake calipers what size Allen wrench do you need to remove those bolts?
3/8" Allen wrench.
What is Another name for an Allen wrench?
An allen wrench is sometimes referred to as a hex wrench or hex key.
What size Allen wrench for 2002 escape front caliper?
7mm Allen wrench
How to compress a 2004 Kia Optima timing belt tensioner?
Use a vice and when fully compressed, insert a tiny(very tiny) Allen wrench into the very tiny hole
What is a Allen Wrench used for?
Allen Screws.
What size Allen wrench and open end wrench for brake pads on 1999 Toyota Corolla?
There is no Allen wrench, I believe it is 14 mm open wrench.
What is an Allen wrench?
An Allen wrench is a hex head wrench - a screwdriver with a handle and hexagonal head at right angles to each other.
Is a torch wrench and a Allen wrench the same?
No they are NOT the same.
How do you remove the center console in a 2000 Ford ranger?
The rear of the console has two bolts on either side. You will need an Allen wrench. Unbolt them and remove the console.
When did James van Allen invented the Allen wrench?
James Van Allen didn't invent the Allen Wrench it was William G. Allen in 1909-1910 of the Allen Manufacturing Company of Hartford, Connecticut.
