This is a 30 amp 125 volt device. The black wire goes on the smallest pin, should be a brass coloured screw, the white on the next in size, should be a silver coloured screw and the ground wire on the pin with the inward hook on it, green coloured screw.
You get a two wire plug!! You should never try to skip connecting the ground wire, the soul purpose of the ground is to create safety for you and others around you. the problem is that someone may assume that the ground is part of the wire since the plug is a three wire!! \You will have to skip the ground terminal on the plug. Usually plug has a green screw or wire, ground pin is longer than two other and round in shape.
In North America the connections for a 15 amp cap (plug) goes as follows. Looking at the plug from the blade side directly on you should see a larger blade (silver) on the right, smaller (brass) blade on the left and a U shaped ground blade on the bottom. The white wire connects under the right (silver) coloured screw, the black wire connects under the left (brass) coloured screw and the green wire under the green ground screw.
Black. wire goes to breaker, white wire goes to neutral bar, and copper wire goes to ground bar.
If the plug is melting it is because of a heat build up caused by loose connections. If the plug is not a moulded plug check that the screws are tight. If it is not that, then the plug blades are not tight enough in the receptacle. Change out the receptacle on the generator. Draw a picture of the receptacle and mark where each wire goes. The best way of doing is is when you have the new receptacle take one wire off of the old receptacle and put it in the same position on the new receptacle. Having tight blade connections will prevent the plug overheating and melting.
Test the wire with a meter to determine which wire is your hot, which is your neutral, and which is your ground. Those colors are indicative of a 240v circuit normally, so you may have two hots and a ground. Other wise Hot=Black, Neutral=White, and Ground=Green for placement. On your plug, Black/Hot goes to the brass colored terminal. Green/ground goes to the sometimes green terminal that is off by itself usually at the bottom of the receptacle. The neutral goes to the silver terminal.
It provides a safe path for errant electricity. Never cut it off.
how to put plug wires on a 1996 Saturn sl
Need to know what engine you have.
With the cover off the plug and looking from the back at the screws the "Live" wire [generally red or brown] goes to the Left - and the "Neutral" wire [generally green] gos to the Right.Another way of putting this would be to say that the red wire must be connected to the prong that goes into the Left hole in the plug outlet in the wall.It is good practice to coil the earth wire in the plug so that, should the lead by tugged hard, it will be the LAST wire to become disconnected from the screws in the plug.AnswerCorrection .... sorry!! With the cover off the plug and looking from the back at the screws the "Live" wire [generally red or brown] goes to the Left - and the "Neutral" wire [generally BLUE] goes to the Right. The Earth [genarally green] goes to the centre prong - assuming it is a 3-pin plug.
http://autorepair.about.com/library/firing_orders/bl-fo-2695.htm which spark plug goes to spark plugs wire set for a Saturn sw 1994
The black wire goes to the brass colored screw and the white wire goes to the silver screw.
A ground wire.
That is the rubber boot that is on the end of the spark plug wire that goes onto the spark plug.
I'm sorry, but WHAT DID YOU DO!?!?!?
If its a v6 the #6 wire goes on the passenger side closest to the firewall. If its a v8 the #6 wire goes on the passenger side 2nd closest to the firewall.
hot wire on the timing light goes to pos. side of the battery and the neg. side of timing light goes to ground on the engine someplace and then the plug clip goes on the #1 spark plug wire.
+ goes to starter solenoid, - goes to distributor side post. center plug wire goes to center plug on distributor.