0
When using a three gang switch plate with 3 spst how many hot wires are needed?
Wiki User
∙ 11y ago
If one circuit contains all three switches and their loads are on the same circuit then only one "hot" and one neutral is needed.
Wiki User
∙ 11y ago
Add your answer:
Earn +20 pts
How is one light controlled by three switches?
That is called a 4 way light switch circuit. On each end of the circuit you install a 3way switch and in the middle you install a 4 way switch.Answer using British TerminologyIn the UK, 'three-way' switches are called 'two-way' switches (more logical, if you think about it!), and the 'four-way' switch is called an 'intermediate' switch.
Can i switch from ketoconazole to clotrimazole?
Yes, you can switch from one to the other, but first make sure you are giving the medicine a fair shot at working; using it as directed for two to three weeks. If there is no result, then switching to a different medication may do the trick.
How do you wire a light switch that has a black common screw and two gold screws one on each side of light switch and a green screw?
That is called a three way switch. It's used in conjunction with another 3 way switch in another area and they both control a light or set of lights. The black is power and the other two are called travelers that wire to the the other 2 gold screws on the other switch. A three way switch can be used as a single pole switch by using the black screw and one of the brass screws. You will have to test the circuit to orient the switch so up is on and down is off, if that is what you desire, because it is not obvious on a three way switch. The green screw is simply your equipment ground. You place your green or bare conductor there.
How do you wire a candelabra lamp to a three way switch?
A candelabra lamp fixture is the same as any other lamp fixture. Using a three way switching system can be followed by the related links.See related links below.
What is the importance of a electric switch?
Electric switch is very important because as you known that all the equipment we are using is useless without a switch. For example, if someone want to turn on its computer, it have to first on the switch without switching on the power supply is not gone in the equipment we using.
How do you make bulb light using a switch?
In a theoretical ciucuit, a switch is not essential. What is needed is a source of electricity.
What is a 3 gang 3 way switch?
3 gang switch and you can call it 2-way switch..is a type of swithces we are using mostly in the stairs lighting ,that mean you have switch up to the stair and one down to the stair and you can switch the light on from one and switch it off from the other switch and via verse. <<>> There is no such thing as a three gang three way switch,. The nearest thing is a three gang double throw switch. It is used to supply a three phase load from two individual three phase supply sources. This is the type of manual switch that can be used for emergency power switch over from utility to generator. Three way switching uses a single pole double throw switch at each end of the circuit and a cross over switch in the center position. The center switch in a three way lighting configuration is a cross over switch and a double pole double throw switch in that position will not work.
What is the operation of a microscope?
fisrt,put the specimen into focus using a lower power lens, then switch to a higher power lens, if needed.
How do you remove ignition switch from steering column on 84 Pontiac fiero?
you have to remove the steering wheel then using a lock plate removal tool depress the lock plate and removed the clip that holds it in place then remove the lock plate then remove the screws from the turn signal switch and pull it up slightly then remove the screw that hold the lock cylinder in place then remove the lock assembly
How do you explode TNT in Minecraft?
TNT can be ignited by using a Flint and Steel on it, or providing charge via a switch (lever, pressure plate, etc) or by an active redstone current.
What is the procedure for the operation of a microscope?
First put the specimen into focus using a low power lens, then switch to a higher power lens if needed.
How do you make a switch?
you may make the switch by following ways :- 1. by using the flip - flops . 2.by using the logic gates according to your desire. you may also make switch by the mechanical process as follows:- 1.take two pcs. of wire 2.take a iron thin and small slide like plate 3.take a spring in the middle of the iron plate 4.attach the wire used to be transmitting in one end 5. press up and down for switching
What is a sentence using the term plate?
I ate dinner on a plate.
What is the correct procedure for the operation of a microscope?
First put the specimen into focus using a low power lens, then switch to a higher power lens if needed.
How many blocks are needed for for a three bedroom bungalow?
The number of blocks needed depends on whether you are using them for the walls or just the foundation, how high the walls are if you are using blocks forthem, the size of the blocks, and what the size of the bungalow will be.
Where is iron plate in Pokemon platinum?
you can get iron plate by using explorer kit
How is one light controlled by three switches?
That is called a 4 way light switch circuit. On each end of the circuit you install a 3way switch and in the middle you install a 4 way switch.Answer using British TerminologyIn the UK, 'three-way' switches are called 'two-way' switches (more logical, if you think about it!), and the 'four-way' switch is called an 'intermediate' switch.
