Where can you find a diagram of the belt routing for a 89 Mercedes Benz 190e 2.6?

Answer 1

http://www.Ford-forums.com/

You can find s to all of your Ford questions. Please feel free to post as much as you like and remember, there is no such thing as a stupid question. Every member is here to learn something new about his or her Ford vehicle. We have many helpful moderators and community members with a wealth of information and knowledge.

You can find owners guide at

http://www.genuineservice.com/genuineservice/en/default?page=Home

Parts at

http://www.motorcraft.com/catalog.do

Autozone do it yourself repair guide

http://www.autozone.com/shopping/repairGuide.htm

About.com Index of Illustrations Ford Auto

http://autorepair.about.com/library/pictures/bl-images_ford-003.htm

Go to this site. Look up your engine and find the belt #. Then click on belt routing and it will show you the diagram

http://www.mvreader.com/multiview/dayco/index.php?bgInterchange=1&l=n

There should be a schematic on the fan shroud. If not, draw one before removing the belt. If the belt is already off, go to a used car lot and find a like car and draw a schematic. Or get a owners manual from MOTORLIT.COM.

Many cars have a diagram under the hood on a decal.

Remove Passenger side tire. Remove splash shield... 90% of belt routing is in plain sight.

Napa auto parts has diagrams.

How to adjust tension

put wrench on tensioner pulley and turn counter clockwise. Its tough to get to. The best way is to remove the plastic guard from under the car and get to it from there. The belt will still be tough to get off but it will go. Two people could do it a lot easier.

How do you install a 98 Escort ZX2 serpentine belt

How-To: Accessory Drive Belt

This document describes how to change the accessory drive belt on a ZX2.

Materials:

Accessory Drive Belt (p/n for A/C JK6-856-AA or 1F1Z-8620-AB) Tools:

10mm socket w/small ratchet 13mm socket w/Large ratchet 1 wire clothes hanger

Notes:

Be sure to get the correct belt. My dealer originally gave me a belt for an 2.0L SPI instead of a 2.0L Zetec, which is over a foot too short.

Removal:

(Optional) Raise and support the vehicle. Remove the 4-5 10mm bolts that hold the shroud underneath the engine. Attach the ratchet w/13mm socket to the belt tensioner bolt, and turn the ratchet towards the rear of the vehicle. This will require some force, as the tensioner is spring loaded. Lock the tensioner in place by placing the ratchet behind one of the bolts of the A/C compressor. Remove the old belt. This may require some twisting, to get the belt out from around the pulleys.

Installation:

Reverse the removal procedure, using the following picture for drive belt routing. The clothes hanger comes in handy here, to route the pulley under the motor mount. I started at the bottom, with the Crankshaft damper and A/C, and worked my way around the tensioner to the generator. Might work better the opposite way, but I wasn't about to pull it back off! Also, if you remove the coolant reservoir to create more space on the top to work. This involves removing the 10mm bolt and 10mm nut that holds it in place. Item Part Number Description 1 10300 Generator pulley 2 19A216 Belt idler pulley 3 3D673 Power Steering pump pulley 4 8509 Water pump pulley 5 6B209 Belt tensioner 6 19703 A/C clutch pulley 7 6B320 Crankshaft pulley damper 8 19A216 Belt idler pulley 9 8620 Drive belt How do you replace the serpentine belt on a 2002 ZX2 Start by making a diagram of the belt route. Have the new belt handy. Raise the car on jack stands or ramps. Locate the tensioner pulley and release the belt tension from beneath the car on the front of the engine. (Bolt head is 14 mm) It will take some work but get the old belt off the car. (Good time to inspect water pump, hoses etc.) Refer to the diagram, route the new belt around pulleys. Leave the belt off the tensioner pulley, and the pulley immediately above it. Push the tensioner pulley back (to release position) and with the aide of an assistant, position the belt on the remainder of the pulleys. Release the tensioner pulley only after everybody is out of the way.