It should be in the main circuit panel. If the dryer was added at some point there may be a separate box just for the dryer either beside the main panel or at the dryer plug. It is not in the dryer itself.
If you are referring to a cloths dryer, the answer depends on the requirements of the dryer. Most dryers require AWG#10 wire with a 30 amp fuse. If the wiring is AWG#12 then use a 20 amp breaker but never use it on AWG#10 which requires a 30 amp breaker. If you are referring to a hair dryer then yes a 20 amp breaker is fine.
No. The two appliances usually have dedicated circuits. The range will have a two pole 40 amp breaker and be fed with a 3-C #8 copper cable. The dryer will have a 30 amp two pole breaker and be fed with a 3-C # 10 copper cable. As you can see by powering a 40 amp device from a 30 amp breaker, full operation of the range will trip the 30 amp breaker.
Single pole 20 amp breaker.
Typically yes if you use a 30 amp breaker and the dryer uses 230-240 volts.
No, a double pole 50 amp breaker protects a 240 volt supply at 50 amps. The number that is on the handle of the breaker is the amperage that the breaker will trip at if an overload occurs on the circuit.
If you are referring to a cloths dryer, the answer depends on the requirements of the dryer. Most dryers require AWG#10 wire with a 30 amp fuse. If the wiring is AWG#12 then use a 20 amp breaker but never use it on AWG#10 which requires a 30 amp breaker. If you are referring to a hair dryer then yes a 20 amp breaker is fine.
no. depending on length of run you'll need either 10 or 6 gauge wire for a 30 amp double pole breaker.
Typical residential electric dryers are on 30 amp circuits, which means 10 gage copper wire. The circuit breaker should match the dryer cord rating, generally 30 amps.
No. The two appliances usually have dedicated circuits. The range will have a two pole 40 amp breaker and be fed with a 3-C #8 copper cable. The dryer will have a 30 amp two pole breaker and be fed with a 3-C # 10 copper cable. As you can see by powering a 40 amp device from a 30 amp breaker, full operation of the range will trip the 30 amp breaker.
You have a double pole breaker for 240Volt supply. The maximum current is 15 amp.
Single pole 20 amp breaker.
In North America the standard sizes for breakers are 15, 20, 30, and 40 amps. The 15 amp size breaker is used in general circuit wiring. The 20 amp size breaker is used for dedicated appliance receptacles, hot water tank and baseboard heating. The 30 amp size breaker is used for a clothes dryer. The 40 amp size breaker is used for the electric range.
Typically yes if you use a 30 amp breaker and the dryer uses 230-240 volts.
No, a double pole 50 amp breaker protects a 240 volt supply at 50 amps. The number that is on the handle of the breaker is the amperage that the breaker will trip at if an overload occurs on the circuit.
Answer for USA, Canada and countries running a 60 Hertz supply service.It is possible to have a dryer that is built to work on a 30 amp single pole breaker but not likely. The most common dryers sold in the U.S. are designed to run on a double pole 220 volts 30 amp circuit. When ever installing electrical equipment it is always necessary to read the manufactures design specifications. They should be clearly marked on the tag with the "UL" seal.
try higher amp breaker
If this is the main service in your home then you probably could not run both appliances at the same time. A range has a 40 amp breaker and a dryer has a 30 amp breaker protecting the feeders to these appliances. Even though both appliances do not draw the maximum current that the breaker allows it would be close. With other devices in use through out the home with the range and dryer on at the same time it will probably trip the panels 60 amp breaker.