2000 Dodge Stratus V-6 2.5 Liter Finding the thermostat: Follow the LOWER radiator hose to where it meets the engine. It's in there. Most cars that I've worked on have the thermostat at the end of the upper radiator hose, but not this car. Replacing the thermostat: You need to remove the thermostat housing. (It's the piece that the lower radiator hose connects to.) - You do not need to remove the radiator hose from the housing. - First remove the bolt that is holding a bracket. This bracket just holds some wires in place. - Now remove the three bolts that hold the housing to the engine block. These bolts can be fairly hard to turn, but just keep trying. - Gently pry the housing away from the engine block. You can use a flat-head screwdriver to help pry, but do not scratch the mating surfaces of the housing and the block. - Pull out the thermostat, noting that the spring end goes into the engine. - When you put the new thermostat in, you probably want to use a new black rubber gasket, but you might be able to use the old one if you have no choice. Also, I didn't add any permatex or anything and it seems fine. - I tightened the bolts to 22foot pounds, but this might be a little high. Whatever you do, DO NOT overtighten the bolts. Couple other notes: I first removed the air cleaner cover and tubes to get a little more working room. I also unplugged one wiring harness to make more room. Otherwise, I was able to get my big hands in there. A new thermostat did not fix my problem. Here is a description of the problem I was having and the solution: Problem: The temperature gauge was spiking occasionally, all the way into the red. It would spike up and come back to normal. It would spike usually while in idle, but sometimes while driving. Usually about once every twenty minutes. Things I checked first: - The plastic reservior for the radiator was full to the top. - The electric fans were running, and running on high speed. - The car had working heat. - Replaced the thermostat. Did nothing to help the problem. Problem Found: - Vapor lock. Even though the reservior was full of fluid, it had previously gotten too low and the system sucked in some air. Once that happens, it doesn't matter if the reservior is full, the cooling system will not draw in the coolant. This is because filling the plastic reservior does not pour coolant directly into the cooling system. The coolant is sucked into the cooling system through a tube, like drinking soda through a straw. So the reservior, where they tell you to add coolant, was full but the cooling system (radiator, engine, pump, etc.) was almost out of coolant and wasn't able to draw in any more. Solution: When the engine is cool, open the metal radiator cap that's sticking right up out of the engine. It can be found by following the upper radiator hose to the engine. There is a tall metal tube with a metal cap on it. Pull that cap off (when it not hot) and fill it up with radiator fluid. (I use radiator fluid that's pre-diluted and designed for all makes and models of cars). Idle the car, in park, for about thirty seconds. Stop the engine and put the cap back on. If you're lucky, all the air bubbles are out of the system and you're all set. Hope this helps! 2000 Dodge Stratus V-6 2.5 Liter Finding the thermostat: Follow the LOWER radiator hose to where it meets the engine. It's in there. Most cars that I've worked on have the thermostat at the end of the upper radiator hose, but not this car. Replacing the thermostat: You need to remove the thermostat housing. (It's the piece that the lower radiator hose connects to.) - You do not need to remove the radiator hose from the housing. - First remove the bolt that is holding a bracket. This bracket just holds some wires in place. - Now remove the three bolts that hold the housing to the engine block. These bolts can be fairly hard to turn, but just keep trying. - Gently pry the housing away from the engine block. You can use a flat-head screwdriver to help pry, but do not scratch the mating surfaces of the housing and the block. - Pull out the thermostat, noting that the spring end goes into the engine. - When you put the new thermostat in, you probably want to use a new black rubber gasket, but you might be able to use the old one if you have no choice. Also, I didn't add any permatex or anything and it seems fine. - I tightened the bolts to 22foot pounds, but this might be a little high. Whatever you do, DO NOT overtighten the bolts. Couple other notes: I first removed the air cleaner cover and tubes to get a little more working room. I also unplugged one wiring harness to make more room. Otherwise, I was able to get my big hands in there. A new thermostat did not fix my problem. Here is a description of the problem I was having and the solution: Problem: The temperature gauge was spiking occasionally, all the way into the red. It would spike up and come back to normal. It would spike usually while in idle, but sometimes while driving. Usually about once every twenty minutes. Things I checked first: - The plastic reservior for the radiator was full to the top. - The electric fans were running, and running on high speed. - The car had working heat. - Replaced the thermostat. Did nothing to help the problem. Problem Found: - Vapor lock. Even though the reservior was full of fluid, it had previously gotten too low and the system sucked in some air. Once that happens, it doesn't matter if the reservior is full, the cooling system will not draw in the coolant. This is because filling the plastic reservior does not pour coolant directly into the cooling system. The coolant is sucked into the cooling system through a tube, like drinking soda through a straw. So the reservior, where they tell you to add coolant, was full but the cooling system (radiator, engine, pump, etc.) was almost out of coolant and wasn't able to draw in any more. Solution: When the engine is cool, open the metal radiator cap that's sticking right up out of the engine. It can be found by following the upper radiator hose to the engine. There is a tall metal tube with a metal cap on it. Pull that cap off (when it not hot) and fill it up with radiator fluid. (I use radiator fluid that's pre-diluted and designed for all makes and models of cars). Idle the car, in park, for about thirty seconds. Stop the engine and put the cap back on. If you're lucky, all the air bubbles are out of the system and you're all set. Hope this helps!
Most automotive thermostats, I believe are located at the engine end of the top radiator hose. But with this car it could be different. In general thermostats are to hold the engine coolant in the engine until it's temp is at the same rating as the stat, usually 180-192 degrees. The stat then opens allowing the coolant to circle into the radiator to begin the cooling process. Hopes this helps you.
On my '95 Dodge Stratus, it is located in a separate relay box located directly above the power distribution box. If you remove the air intake hose, you will see it. To access it, you will need to remove the air intake hose, move the cover for the remote positive battery terminal, and remove the rear cable for the PCM. Inside this relay box are the fan relays (hi and lo), the starter relay and the ASD relay. Hope this helps.
The thermostat is located on top of the engine, you have to remove the alternator and the alternator bracket to access the thermostat, I'm going out to do mine right now! have fun! It is under the housing where the upper radiator hose hooks to.
The thermostat on your 2002 Dodge Grand Caravan 3.3 liter engine is located in the thermostat housing. The thermostat housing can be found on the front of the engine.
under the housing that the upper radiator hose connects to
On the intake manifold at the end of the upper radiator hose.
put your hand on the top radiator hose, follow it back to where it connects to the engine. That part is called the thermostat housing, inside there is the thermostat.
How do I replace the heating coil in a 2006 Grand Caravan? I have no heat it only blows cold air.
Almost all thermostats are located where the top radiator hose attaches to the engine.
Dry fill is about 9 quartsDry fill is about 9 quarts
The EGr valve can be difrent and is in difrent locations on the various engines
yes
where is the transmission fluid pressure sensor located o a 2005 dodge grand caravan
Spring towards the engine.
on the intake
A 2005 Dodge Caravan does not have a manometer.
The crankshaft position sensor on a 2005 dodge grand caravan is mounted on the upper side of the bell housing and can be easily accessed from the top.
The fuse for the cigarette lighter on a 2005 Dodge Grand Caravan is located inside the van. The fuse box will be on the drivers side.
The 2005 Dodge Grand-Caravan has 12 valves.
The 2005 Dodge Grand-Caravan has a V6 engine.
The 2005 Dodge Grand-Caravan has a 4-speed automatic.
The 2005 Dodge Grand-Caravan is a gas-powered vehicle.
The 2005 Dodge Grand-Caravan has overhead valves (OHV).
How much dose a 2005 dodge caravan sxt get a mile