answersLogoWhite

0


Best Answer

bulk oil circuit breaker

User Avatar

Wiki User

11y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: Which circuit breaker is preferred for extra high tension application?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

Can you use the vacuum circuit breaker instant of air circuit breaker?

Actually ACB isused for Low Tension side and VCB is used for High Tension Side..Chappa matter


What device can break an electric circuit?

There are 2 different types of these devices: circuit breakers (which can be reset after the problem is fixed) and fuses (which must be replaced after the problem is fixed).


What is ice breaker?

An ice breaker is something to start a conversation or to relieve tension or inhibitions between people.


Types of circuit breakers?

There are several type of circuit breakers now a day we are using these are as follows: 1. M.C.B. (Miniature circuit Breaker) Rating : 1, 2, 4, 6, 10, 16, 20, 25, 32, 63 Amperes 2. M.C.C.B. (Miniature current circuit Breaker) Rating : 10, 16, 20, 25, 32, 63, 100, 200, 250, 400 Amperes. 3. A.C.B. (Air Circuit Breaker) Rating : 400, 800, 1000, 1200, 1500, 1800, 2000 Amperes. 4. A. B. Switch (Air Breaker) used in High tension line. 5. SF6 Breaker (Contact break in the Sf6 medium) used in High tension line.


What caused tension between the north and the south?

California's application for statehood.


How do you install the AC belt on an '88 Lincoln?

1. Loosen the idler pullery bracket adjustment and pivot bolts. 2. Position a suitable belt tension gauge. 3. Install a 1/2 in. breaker bar in the hole in the idler pulley bracket. Apply tension to the belt using the breaker bar. 4. Set the tension on a new belt to 170 lbs or a used belt to 140lbs. While maintaining the tension, tighten the adjustment bolt to 30ft. lbs 5. Remove the belt tension gauge and the breaker bar. Start the engine and let it idle for 5 minutes. 6. Shut the engine off, then reinstall the belt tension gauge and breaker bar. Apply tension with the breaker bar and slowly loosen the adjustment bolt to allow belt tension to increase to the used belt specification, 140 ft. lbs. Tighten the adjustment bolt to 30 ft. lbs. 7. Tighten the pivot bolt to 50ft. lbs.


How do i loosen the tension belt on a 98 cavalier 2.2?

The tension pulley has a 3/8" square hole in it. Using a 3/8 drive ratchet or breaker bar, simply put it in and pull the tension pulley.


How do I replace the serpentine belt on a 2004 Matrix?

First you need a breaker bar and 19mm socket to fit the "tension bolt". Turn tension bolt clockwise to release tension in order to remove the serpentine belt.


How do you release the serpentine belt located on a Mercury Tracer?

There is a tensioner located towards the front of the engine. You'll need a fairly long handle ratchet, a breaker bar preferred. In any event you'll have to determine what on your model has to grab a hold of, release the tension and slide the belt off of which ever pulley is close. Then relaese the tension SLOWLY!!! there is a lot of tension on it and it could snap out of your hand. then reverse the process only retract the tensioner at the end when your ready to put the belt on your last pulley.


Does a resistor only decrease current in a circuit?

A resistor does not only decrease current in a circuit it can also reduce tension(voltage) if connected in series.


Release the tension on the belt alternator on a 1996 Lincoln mark 8?

You have to use a 1/2 inch breaker bar and put it in the square hole of the tensioner and turn it to release the tension of the belt.


Loosen belt tension 2006 powerstroke diesel 6.0?

Use a 1/2" drive breaker bar in the tensioner.