By inventing something one creates something that wasn't and creates something that is. Amperage was always there, and various people characterized what was meant by current and how it manifested itself under certain circumstances. For example, in a lightening strike there is a lot of current flowing through the air. Imagine Ben Franklin flying his kite in a storm. He was trying to see how one could harness the power of electricity.
For more info research the following individuals:
André Ampère (1775-1836)
Alessandro Volta (1745-1827)
Georg Simon Ohm (1787-1854)
Ernest Rutherford (1871-1937)
Benjamin Franklin (1706-1790)
Thomas Alva Edison (1847-1931)
Michael Faraday (1791-1867)
Nicholas Tesla (1856 - 1943)
An ammeter is a tool used to measure electric currents. The ammeter was discovered in 1820 by Hans Christian Orstead.
There are several amperage ratings on AC compressors/motors. Locked Motor Amperage (LRA) is the amperage that the motor is fused for. The load of the motor is expressed in amperage or wattage, which is probably the case here. Low amperage readings on an AC unit being charged by amperage load would indicate low freon. High amperage readings indicate overcharge when charging by the amperage load. AC units are not accurately charged by amperage readings and the efficiency of motors is not expressed in amperage readings.
Voltage is equal to amperage time resistance. V=IR Therefore, I'd say voltage times amperage is equal to amperage squared times resistance. VI=IIR Really there's no point in multiplying the two. However, if you were to divide voltage by amperage, you would have the resistance of the circuit. V/I=R
The relation between amperage and capacitance is that amperage is equals to capacitance times the rate of voltage change over time. This voltage refers to instantaneous voltage.
The 225 amps is the secondary output amperage. Look on the machines nameplate to find the input amperage. It is that amperage that is needed to size the feed wire and there the breaker size. When you find that amperage you may want to re question the breaker size.
With kitchen tongs. A mild tingling indicates low voltage/low amperage. Muscular spasms indicate high voltage/low amperage. Unconsciousness sans death indicates low voltage/moderate amperage. Death indicates high amperage. Good luck.
Amperage is electric current of flow.
The amperage of a T2L 250v fuse is typically 8 amps. It is a misconception that it has an amperage of 3.
There are several amperage ratings on AC compressors/motors. Locked Motor Amperage (LRA) is the amperage that the motor is fused for. The load of the motor is expressed in amperage or wattage, which is probably the case here. Low amperage readings on an AC unit being charged by amperage load would indicate low freon. High amperage readings indicate overcharge when charging by the amperage load. AC units are not accurately charged by amperage readings and the efficiency of motors is not expressed in amperage readings.
It is ok to use a fuse with a higher amperage rating and not ok to use a fuse with a smaller amperage rating why?
This doesn't make sense, "current" is "amperage" so the higher the voltage the lower the amperage, and the lower the voltage the higher the amperage.
Voltage is equal to amperage time resistance. V=IR Therefore, I'd say voltage times amperage is equal to amperage squared times resistance. VI=IIR Really there's no point in multiplying the two. However, if you were to divide voltage by amperage, you would have the resistance of the circuit. V/I=R
There is no proper amperage...no such thing as amperage, its called current... measured in amps...
Wire size is based on the amperage drawn. To find the amperage, the voltage must be stated. Use this formula to find the amperage. I = W/E. Amps = Watts/ Volts. Once you have the amperage, restate your question using the new found amperage or state the voltage that supplies the lights.
An amperage is the electric current's strength carried by a conductor or machine generated as measured in amperes.
How much amperage for a hotpoint 20 inch stove
a ten-wrap amperage multiplier is used with a (n)
The amperage is governed by the load that is connected to the battery circuit. Divide that amperage into the 1.6 amp hours and that will give you the endurance of the battery in hours.