Most compact fluorescent lamps won't work with conventional dimmers, or will damage the dimmer.
Magnetic dimmers will work, however. Answer
Actually, it depends on the design of the lamp. Different companies have different power supplies for the lamps. What works well on one can spell instant death for another. Get a dimmable lamp. The new LED lamps have the same problem. Some work fine with a dimmer, provided one incandescent lamp is left in the fixture. Others go crazy.
The trip odometer switch on the odometer itself is the dimmer on Toyota Sienna. If you turn this switch all the way to the left your panel would become dark. Simply turn the switch to the right and all panel lights would come on. I had a similar problem and the manual bailed me out.
Your question is a bit unclear and vague, but if you have a dimmer switch and you turn it all the way to its lowest setting then the switch should not fail because of that. If there is nothing wrong with your electrical system then using a device exactly how it was designed to be used then there is no reason why it would catch on fire.
This type of circuit would never be used. The two way fluorescent system would depend on the voltage being supplied by the two lamp circuit switch. If the switch turns off the two lamp circuit the rest of the circuit with the fluorescent fixture would become inoperable.
A 3-way incandescent bulb works by having two separate filaments for the first two levels of brightness. For example, a 30-70-100 bulb will have a 30 watt filament and a 70 watt filament. The 3-way switch then turns on either the 30, the 70, or both - giving the 100 watts full brightness. (This is why a 3-way incandescent bulb usually burns out the most commonly used brightness level first.) A 3-way compact fluorescent, using the same simple 3-way switch, will either have two separate fluorescent tubes, one for each of the first two brightness levels (unlikely), or it will adjust the brightness electronically through an internal voltage (or other) adjustment based on which position the 3-way switch is set at. This is only an approximation - additional details would be interesting.
For the most convenience, you should consider replacing two switches with just one switch that does both tasks. The first thing to do before repairing anything electrical is turn off the electricity to that room, then repair or replace the switch as you would any other light switch.
If you have another CFB try it in the same position as the one that is not working. It sounds like the CF bulb is defective.
Yes, compact fluorescent lamps can be dimmed. However it requires a dimming ballast which can be quite expensive and the amount of dimming is limited to about 20%. If you're thinking of using a dimmer you would be better off using an incandescent lamp.
You would have to use a dimmer switch I would think.
A dimmer switch is used for lighting loads and not heating loads. The wattage rating on a dimmer switch is what the manufacturer recommends as the maximum load that the switch can handle. For example if you have ten 100 watt lamps, the total load wattage would be 1000 watts (10 x 100). Too much load for a 600 watt rated dimmer switch but not for a 1000 Watt rated dimmer switch. So you can see that the rating on a dimmer switch governs the maximum wattage load that can be connected in the circuit that is to be controlled.
I would suspect the dimmer switch or "combination switch".
Yes, it could.
i would say that your dimmer switch is probably broken
The trip odometer switch on the odometer itself is the dimmer on Toyota Sienna. If you turn this switch all the way to the left your panel would become dark. Simply turn the switch to the right and all panel lights would come on. I had a similar problem and the manual bailed me out.
the low beams should not be on a fuse it will either be the dimmer switch or the headlight its self. for your problem i would check the dimmer switch first J.
Your question is a bit unclear and vague, but if you have a dimmer switch and you turn it all the way to its lowest setting then the switch should not fail because of that. If there is nothing wrong with your electrical system then using a device exactly how it was designed to be used then there is no reason why it would catch on fire.
This type of circuit would never be used. The two way fluorescent system would depend on the voltage being supplied by the two lamp circuit switch. If the switch turns off the two lamp circuit the rest of the circuit with the fluorescent fixture would become inoperable.
Its the dimmer switch bad.