Yes, if you use two 4 ohm speakers or or one 4 ohm resistor and a 4 ohm speaker to equal the 8 ohm resistance per channel. An important thing to note about this, is that you will need to make sure you get a resistor that can handle the current. You can go higher in resistance but not lower, it must be equal to or higher. Something important is added: The amplifier will have an output impedance of around 0.04 ohms. In hi-fi we have always impedance bridging. Zout << Zin. The damping factor DF = Zin / Zout tells you what Zout is. Zout = Zin/DF. If the damping factor DF = 200 and the loudspeaker impedance is Zin = 8 ohms, the output impedance of the amplifier is Zout = 8 / 200 = 0.04 ohms. You see, there is no "8 ohm amplifier" with a 8 ohm output. Scroll down to related links and look at "Voltage Bridging - Zout << Zin".
Yes, but:
1.) if the amplifier is not rated for 4 Ohms, it may become overloaded at moderate volumes, overheat, and burn out.
2.) A 4 Ohm speaker will draw twice as much power from a typical solid state amplifier as an 8 Ohm speaker. Therefore the volume will be incorrectly high.
3. ) If you must use the 4 Ohm speakers, put a 4 Ohm resistor in series with them to make a total of 8 ohms. The speakers will play at half power. The resistor must be rated for half the power of the audio output channel in question. It may become hot and should be mounted away from items that might burn or melt.
Amplifiers are rated to operate with certain speakers. Most speakers on the market have an 8 ohm impedance and many amplifiers are designed to drive 8 ohm speakers. In most cases, an amplifier will operate with a 4 ohm speaker but there is a possibility that as the output level increases, the amplifier may be damaged due to excess current being drawn by the speaker.
With all amplifiers, it is worth checking the manual to see what the manufacturer advises regarding lower impedance speakers.
As an additional note, it is worth mentioning that amplifiers have an output impedance that is far lower than the rated load impedance. Therefore, there is strictly no amplifier that has 8 ohm outputs. For more information on this aspect, see the link below.
There is really no amplifier with an output of 4 ohms. All loudspeaker amplifiers have an output impedance of 0.5 ohm or less. Scroll down to related links and look at "Voltage Bridging".
Sorry, there is no 4 ohm amplifier in the world. All loudspeaker amps have an output impedance of less than 0.5 Ohm.
Never heard of an amplifier with 4 ohms output impedance. It's always much less than 0.5 ohms. 4 ohms or 8 ohms amplifier are a myth.
if you put 2, 8 ohm speakers together on the same channel you will trick the amp into seeing a 4 ohm load, it is not advisable to run a 8 ohm coiled speaker on a 4 ohm amp unless you do the above. So if you want to run 2 8 ohm speakers from a 4 ohm amp this will work the best although the amp will need to be hefty as its worse to underpower a sub than overpower it! I have used a 8 ohm speaker myself on a car amp and had no problems but it was not a cheap entry level amp! some amps will take it, others will get hot and enter protection mode. Hope this helps!!!
nope
You could go with a 600 watt 2 ch amp or a 300 watt mono block amp, depends on what OHM the subs are, if they are 8 ohm you could wire them down to 4 ohm or if they 4 ohm u could wire them to 2 ohm, i have a 600.1 Boss amp and subs are wired together at 2 ohm and they BANG.
Don't know how you have subs wired but should be 4 ohm load is what your amp will see.
Of course! As long as your amp's minimum impedance is 4 ohms or lower.
The sound quality won't be very good
There is really no 4 ohm amplifier. The output impedance of a good amplifier is less than 0.5 ohms. Scroll down to related links and look at "Voltage bridging or impedance bridging - Zout < Zin - Interconnection of two audio units".
Yes, the L-7s are great. For the amp, you first need to find out whether the sub woofers are 2-ohm, 4-ohm, or 8-ohm. Depending on the answer to that question will determine whether or not you'll need a mono amp or a dual channel amp as well as the wattage.
There is really no amplifier with an output of 8 ohm or 4 ohm. All loudspeaker amplifiers have an output impedance of 0.5 ohm or less. Scroll down to related links and look at "Voltage Bridging".
If you connect two 8 ohm speakers to the average car amp, then yes, probably. Most car amps can handle a 4 ohm load, which is what it would be.
Sure, If you mean your stereo has 4 ohm output and using 16 ohm speakers. The volume will be reduced somewhat by doing this, but it won't harm the stereo. If you have 4 ohm speakers and stereo is designed for 16 ohms you can do it ,but the amp will run hot and you may suffer damage at high volume to the amp.
You will find no 4 ohm amplifier! So you will need no transformer. All audio amplifiers have output impedances of lower than 0.5 ohms. We have "impedance bridging" between amplifier and loudspeaker - no matching. Scroll down to related links and look at "impedance bridging - Wikipedia".