0
MAINT REQD on means its time to replace your engine oil. The indicator lamp stays on until it is reset. To reset this reminder: While the ignition switch is on, but the engine is not running, move the trip selector to ODO. Push and hold down the trip selector push knob. Turn off the ignition switch, then turn on the switch. The reset will go through 000000.0 then ------, -----, ----, ---, --, -. once it runs through, release the trip selector knob. The MAINT REQD lamp goes out.
Wiki User
∙ 15y ago
Add your answer:
Earn +20 pts
How do you reset maint req light 2007 Camry le?
The answer is in the manual.
How do you reset the maintenance light for oil changes on a 2007 Toyota 4Runner?
Turn the 4Runner on, make sure that you are looking at the "odometer" miles and not the "Trip" miles. Turn the 4Runner off, hold the "reset" button, turn the 4Runner On and the "MAINT" light will blink 3 times. Release the "reset" button and the light will turn off. This worked great for me but the light flashed 5 times then went off. 2007 SR5 4WD 16,000 miles recently purchased from dealer hopefully there is nothing else wrong/ FYI the manual told me that the maint light is for oil change.
How do you reset the check engine light on a 2007 Toyota Corolla?
Try unhooking your battery cables for a few minutes. That usually works for me.
How do you turn off the required maintenance warning on a 2007 4 runner?
You may have to repeat this several times until you accomplish the task. Select the odometer total miles with the trip reset switch. Turn off ignition and then turn on again depressing the reset switch and holding it until the maint light begins blinking. Continue pressing on the switch until the maint light goes out.
How do reset the maint req light on a 2007 Toyota Camry 2007 SE after oil change?
Set the odometer to the trip A setting, turn off the car, then turn the key to the accessory position while holding down the trip reset button, this should turn it off.
Why Maint reqrd light on 2007 camry7500 miles?
cause u need an oil change
How do you reset low tire pressure warning light on a 2007 Toyota Corolla?
You have to hold the tire pressure button down until the light starts flashing, after 5 seconds press the button again( do not hold it). This will reset the system, and recalibrate it to the new tires
How do you reset the maintenance required light on a 2007 Toyota Sienna?
1. Ensure odometer is showing total miles (not one of the "trip" miles). 2. Turn the ignition key to the "OFF" position. 3. Push the trip odometer reset button and hold it "in." 4. WHILE HOLDING DOWN THE RESET BUTTON, turn the ignition key to "ON" and continue to hold the reset button down until the odometer reading shows "------" and the "maint required" light goes off (about 5 seconds). 5. Release the reset button and total miles will return and the maint required light stays off! I got this answer from WikiAnswers for the 2004 Sienna. If my answer doesn't make sense, look at that guy's.
How do you reset 2007 Toyota Sienna check engine light?
How to Reset the "MAINT REQD" Light on Toyota Sienna With the car started (ignition on), set the LCD odometer readout to total mileage (not trip A or B). Turn the car off (ignition key to the OFF position). Push in AND HOLD the button/knob that switches the odometer Turn key to ON position without starting the car. You will notice the maintenance light blink and go out. Release the odometer button/knob. Turn key to OFF position. That's it! The "MAINT REQD" light has been reset to warn you to change your oil in another 5,000 or 7,500 miles or so.
How do you reset oil change light on a 2007 Ford Taurus?
o I want to reset the oil light on my 2007 mustang 6cyl.
2007 Hilux D4D T Belt light reset?
You will first need to properly reset the light. If this does not reset the light, then you may have to manually press it.
How do you reset maintenance reminder light 2008 Toyota Corolla?
How do you reset maintenance reminder light on 2008 Toyota corolla? For what it is worth: To reset the Maintenance Required light on my 2007 Toyota Corolla: 1) Set your trip meter to the odometer setting (in other words, not Trip A or Trip B) 2) Hold down trip meter reset button and turn ignition to off. 3) While holding down the trip meter reset button now turn the ignition to on. 4) Keep holding down button until Maintenance Required light shuts off. Note: One some other Toyota models you hold down the Trip A meter rather than the odometer. Hope this works for you.
