answersLogoWhite

0


Best Answer

what size and style? If it is butt weld you half the pipe size 3 times and take the 2nd and 4th number and add together. 6 inch example below....

1] 6"
2] 3" add this
3] 1 1/2"
4] 3/4" and this................so 6 inch 45 would be 3 3/4"






you also can use this formula.. pipe size times 0.625 [ 5/8 ]

User Avatar

Wiki User

14y ago
This answer is:
User Avatar
More answers
User Avatar

Wiki User

12y ago

There is no one formula for fitting take offs. The general rule used for gal and black malleable fittings is on a center to center measurement to take off the ID of the pipe you are using on each end of the pipe. Example if center to center measurement is 10 feet between a 1 inch tee and a 1 inch 90 ell. The end to end measurement would be minus 2 inches for a total of 9 foot 10 inches. If you are a industrial pipe fitter there is a pipe fitters blue book that covers all this and a lot more,but the formula we use is take the size of the fitting and break it down 4 times add the second and forth dimension together and there's your take off,ex. 10 inch 45 degree carbon steel would be like this,,,,,10-5- 2.5-11/4=6 1/4 take out.......

This answer is:
User Avatar

User Avatar

Wiki User

11y ago

One and 7/8"

This answer is:
User Avatar

User Avatar

Wiki User

12y ago

3 inch

This answer is:
User Avatar
User Avatar

Rex Evans

Lvl 1
1y ago
Multiply pipe size by .294

User Avatar

Anonymous

Lvl 1
3y ago

.625

This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: What is the take off measurements for 22.5 degree pipe fittings?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

What is the Take off measurements for 90 degree pipe fittings?

If it is 3 in. Then take off 3 in. and so on for what ever size you are use if it is 2 in. then 2 in.


What is pipe take off?

It is the measurement of fittings for piping. It is the measurement of fittings for piping.


What is the take off formula off 45 degree elbow pipe?

The take off formula of a 45 degree elbow pipe, will depend on what the pipe is on. Sometimes a 45 degree pipe will need a 90 degree right angle turn to come off.


What is the pipe formula for the take off of a tee?

The same as a short radius 90 of that same pipe size. I Rule of thumb, for example: 1/2 inch copper tubing you would take off 1/2 inch, likewise 3/4 tubing take 3/4 inch. Your question is 'pipe' are you actually using pipe, cutting and threading pipe? I am often asked questions and find that people are not using 'pipe'. Copper tubing, pvc, cpvc, dwv are quite forgiving when it comes to a slight miscut. Iron and galvanized piping is a different story, get it right the first time!


What is the take out of 6 inches socket weld 90 degree elbow?

what is the take out of 6 inches pipe of a socket weld 90 degree elbow


What is the take out of a 6 inches socket weld 90 degree elbow?

what is the take out of 6 inches pipe of a socket weld 90 degree elbow


What is the take off for a 90 degree angle?

It's your pipe size multiplied by 1.5


How do you solder copper to brass fittings?

Take either an SOS pad or a wire brush and rough up both the inside of the brass fitting and outside of copper pipe, put the copper pipe into the fitting and solder around it.


How do you get the take off 90 degree elbow pipe?

Measure to the center of the Ell and decuct for the threads ..


How long would it take 150 degree water to reaching freezing point in 2 insulated pipe exposed to 0 degree temperature?

Without knowing how fast the heat leaves the pipe, this cannot be answered.


1989 Chevy Astro Van has a coolant leak at the fitting were the heater circuit pipe attaches to the intake manifold near the distributor How does this fittings come apart?

It snaps in. But before you snap it out, take the nut out that holds the pipe to the exhaust manifold.


How much more pressure does it take to push water up a vertical pipe than if the pipe is on a 45 degree angle?

it takes the same pressure if the vertical heights the same but since the 45 degree pipe would be longer it would create more flow restriction.